Jeep WJ Grand Cherokee Radio Antenna Removal

By Jeep Experts

Welcome to the jeepExperts.com in-depth web page on WJ Generation Jeep Grand Cherokee antenna removing. We have organized as a lot data as we may discover right into a useful article beneath. Is one thing incorrect or lacking? Please get in contact with us and we’ll repair it!

Antenna removing

1. Disconnect and isolate the battery destructive cable.

2. Remove the scuff plate from the best entrance door sill. The sill trim molding is held in place with molded in snap retainers. Using a trim stick C-4755 or equal, rigorously pry up one nook of the sill trim. Grasp the sting of the trim and pull up gently to launch the snap retainers.

3. Remove the trim panel from the best interior cowl facet by eradicating the screws attaching the cowl trim to the ground. Remove the plastic nut. Grasp cowl trim and pull outward to separate from clip.

4. Reach underneath the passenger facet of the instrument panel close to the best cowl facet interior panel to disconnect the antenna coaxial cable connector by pulling it aside whereas twisting the metallic connector halves. Do not pull on the cable.

5. Remove the decrease rear half of the interior liner from the best entrance fender wheel home. This could require eradicating just one or two of the plastic rivets. The rivets may be minimize off by sliding a knife underneath the top, or by drilling out via the middle of the highest with a drill. For extra data on the plastic rivets see Grille and fascia removal.

See also  Jeep WJ Grand Cherokee Ambient Temperature Sensor And Display

6. Reach via the rear of the best entrance fender wheel home opening to entry and unseat the antenna lead grommet from the outlet in the best cowl facet outer panel.

7. Pull the antenna lead coaxial cable and connector out of the passenger compartment and into the best entrance fender wheel home via the outlet in the best cowl facet outer panel.

8. Unscrew the antenna mast from the antenna base.

9. Remove the plastic shroud from the antenna base cap nut.

10. Remove the antenna base cap nut utilizing an antenna nut wrench (Special Tool C-4816).

11. Remove the antenna escutcheon from the antenna base on the highest of the best entrance fender.

12. Lower the antenna base from the mounting gap within the high of the best entrance fender.

13. Remove the antenna base and lead from the rear of the best entrance fender wheel home opening.

Antenna set up

1. Position the antenna base and lead into the rear of the best entrance fender wheel home opening.

2. Insert the antenna base into the mounting gap within the high of the best entrance fender.

3. Install the antenna escutcheon onto the antenna base on the highest of the best entrance fender.

4. Install and tighten the antenna base cap nut utilizing an antenna nut wrench (Special Tool C-4816). Tighten the cap nut to six.8 N·m (60 in. lbs.).

5. Install the plastic shroud onto the antenna base cap nut.

6. Using a wrench, set up and tighten the antenna mast onto the antenna base. Tighten the antenna mast to three.3 N·m (30 in. lbs.).Ensure that the antenna mast is absolutely seated on antenna base and that there isn’t any hole between the mast and base.

See also  Jeep WJ Grand Cherokee Aftermarket Cabin Air Filter Accessory

7. Reach via the rear of the best entrance fender wheel home opening to entry and insert the antenna lead coaxial cable and connector into the passenger compartment via the outlet in the best cowl facet outer panel.

8. From the best entrance fender wheel home, seat the antenna lead grommet into the outlet in the best cowl facet outer panel.

9. Install the decrease rear half of the interior liner into the best entrance fender wheel home.

10.reconnect the antenna coaxial cable connector halves.

11. Install the trim panel onto the best interior cowl facet.

12. Install the scuff plate onto the best entrance door sill.

13. Reconnect the battery destructive cable.

Leave a Comment